Hot Working Die Steel 4Cr5MoSiV1 H13 for Die Casting and Forging
Release time:
2026-11-18
Zhenbang supplies hot working die steel in the 4Cr5MoSiV1, H13, 1.2344 and SKD61 grade. The product page describes 4Cr5MoSiV as a benchmark grade for hot work tools, with a balance of cost and performance.
Grade and Smelting Control
The grade is produced by electric arc furnace primary melting, ladle refining and vacuum degassing. The page gives control limits of sulfur up to 0.005 percent, phosphorus up to 0.015 percent and oxygen up to 15 ppm. For high end batches, electrostatic remelting is used and the oxygen content is reduced to 8 ppm or less, with inclusions A, B and C held to grade 1.0 or finer under ASTM E45.
Those limits matter in a hot work die because impurities and inclusions act as crack starters under thermal cycling. A buyer who is specifying the steel for a long run die should ask for the smelting route on the certificate. The same page states that ultrasonic inspection follows SEP 1921 or ASTM A388, with a defect limit of 2 mm equivalent for the ordinary grade and 1 mm equivalent for the ESR grade on a full section.
The delivery condition can be annealed or pre-hardened. Annealed stock is listed at 220 HB or lower for heavy cutting and etching. Pre-hardened stock is listed at 38 to 45 HRC for direct finish machining without heat treatment deformation. The choice depends on how much machining the die shop wants to do before the final heat treatment.
Heat Treatment Window
The page gives a full heat treatment route. Annealing is carried out at 850 to 880 C with slow cooling to 500 C, followed by air cooling, to reach a hardness of 220 HB or lower. Quenching is carried out at 1020 to 1050 C in oil or gas, giving 52 to 56 HRC with a grain size of ASTM 8 to 10. Tempering is done twice, first at 540 to 600 C and then at 560 to 620 C, to reach 45 to 52 HRC.
The page warns against tempering in the 500 to 550 C range because of the brittle interval. Large modules should be heated in steps, allowing about one hour for each 25 mm of thickness. These are practical instructions for a die shop, not a substitute for the supplier review of the actual block size and furnace.
Forging is described as multi-way upsetting and drawing with a forging ratio of at least 3. The initial forging temperature is 1100 to 1150 C and the final forging temperature is 850 C or higher. A buyer who purchases forged blocks should ask for the forging ratio and the final forging temperature on the test report.

Mechanical and Surface Properties
The page lists a room temperature impact toughness of at least 25 J in the conventional heat treatment state, and an impact energy of at least 15 J at 600 C. The high temperature data is the part that matters for die casting and hot forging, where the die surface sees repeated heating and cooling. The page also states that thermal fatigue resistance is better than 3Cr2W8V.
Hardenability is listed as uniform across a 150 mm section, with a hardness fluctuation of plus or minus 2 HRC. The annealed state is described as easy to machine, and polishing can reach Ra 0.05 micrometres or better. The grade is compatible with nitriding to a surface hardness of 1000 HV or higher, and with PVD coatings such as CrAlN.
Sizes and Applications
Round bars of the hot working die steel are listed from 20 to 600 mm in diameter and 1 to 6 m in length, with black skin or fine grinding to Ra 0.8 micrometres. Plates are listed from 20 to 300 mm in thickness and 1000 to 2500 mm in width, in hot rolled or milled condition. Squares run from 50 by 50 mm to 400 by 400 mm, with a special precision insert option.
The page lists three main application groups. For die casting, the grade is used for aluminum and magnesium alloy cylinder bodies and sprue bushes, where resistance to molten metal erosion up to 600 C is the key point. For hot forging, it is used for crankshaft and connecting rod dies up to 400 mm thick, where impact resistance and high temperature stability matter. For extrusion, it is used for aluminum extrusion cylinders and related tooling.
To request a quotation, send the grade, the delivery condition, the size and the quantity. State whether the block is for die casting, hot forging or extrusion, and include the heat treatment route if the die shop has one. Ask for the mill certificate, the ultrasonic report and the forging ratio with the offer.
For the hot working die steel range, contact info@hbzbmj.cn or reach the sales team on the numbers listed on the product page, +8615572985655 and +8617671227388. Our team can confirm the available stock size, the ESR option and the delivery schedule for the grade you need.
Previous page
Previous page
Related news
Address: No. 128, Zhang Zhihe Avenue, Dapaishan Village, Xisaishan District, Huangshi City, Hubei Province